MPI-530-IT Multifunction Electrical Installation Meter
Bluetooth Mini Keyboard (optional)
Measurement of short-circuit loop impedance:
- impedance measurement with resolution 0.001 and 23 A current
(44 A phase-to-phase)
- short-circuit resistor R =10 ZW
- measurement range: 95...440 V, frequency 45...65 Hz,
- measurement of short circuit loop impedance with resolution 0.01 ,
in protected systems without tripping the RCD’s with I ≥ 30 mA Δn
- automatic calculation of short-circuit current, differentiating
between phase-to-phase and phase-to-neutral voltage,
- measurements using UNI-Schuko plug with measurement
triggering button (also when L and N leads are exchangeable) or
1.2 m, 5 m, 10 m, 20 m test leads, with optional use of 3-phase
socket adapters (AGT),
- selection of installation protections and automatic evaluation of
measurements results
Examination of AC, A and B type residual current devices::
- MPI-530-IT allows measurements in IT network,
- measurement of general, short-time delay and selective RCDs of
rated residual current 10, 30, 100, 300, 500 and 1000 mA,
- a function of automatic measurement of the full set of RCD
parameters (after a single push of the "START" button, the meter
performs the entire defined cycle of measurements, including the
L-PE short-circuit loop impedance measurement with 15 mA
current),
- the shape of leakage current characteristics selected by the user:
sinusoidal (starting with the rising or falling edge), pulsating
unidirectional current (positive or negative), pulsating unidirectional
current with 6mA direct current offset (positive or negative),
direct current (positive or negative),
- measurement of the I operating current with rising current, A
- measurement of the t tripping time for I , I , 2I , 5I , A Δn Δn Δn Δn
- measurement of the U touch voltage and the R protective
conductor resistance B E without tripping the RCD,
- detection of swapped L and N conductors in a socket; no influence
on the performance of measurements,
- capability of the I tripping current and the t actual tripping time
measurement A AI with just one RCD tripping,
- voltage measurements in the range of 95...270 V.
Insulation resistance measurement:
- test voltages: 50 V, 100 V, 250 V, 500 V, 1000 V,
- insulation resistance measurements up to 10 G ,
- capability of in-socket measurement with the use of the UN
Schuko adapter,
- acoustic signalling of 5-second time intervals to facilitate capturing
time characteristics,
- protection of the meter against the presence of voltage on the
object and the appearance of voltage during measurement,
- automatic discharge of capacitance of the object after finishing the
measurement,
- automatic measurement of all resistance combinations of 3, 4 and
5-core cords with the use of the additional AutoISO-1000C
adapter.
Measurements of earth resistance and earth resistivity:
- measurement with 3- or 4-lead technical method and 2 auxiliary
electrodes,
- measurement with the 3-pole method with and additional clamp,
- measurement with 2-clamp method,
- measurement of earth resistivity - range of measurement: 0.0 Ωm
...9.99 kΩm, input of rods spacing distances in meters (1...30 m)
or in feet (1...90 ft)
Key Features:
-
Measurement and recording of voltage, frequency, AC, cosφ and power
(active, reactive and apparent), voltage and current harmonics up to 40,
THD.
-
Quick verification of correctness of the PE conductor connection with the use of a touch electrode.
-
Phase sequence checking.
-
Innovative memory with description of measurement points, facilities,
names of customers (max. 10000 results of each measurement).
-
Power supply from rechargeable of disposable batteries (optional).
Low-voltage measurement of protective connection
and equipotential bonding resistance:
- measurement of the protective conductor continuity with current 200 mA
in both directions (in accordance with the EN 61557-4 standard),
- low-current measurement of resistance with acoustic and light signalling,
- automatic calibration of test leads - capability of using test leads of any
length.
Specifications:
Electrical safety
- type of insulation: double, according to EN 61010-1and IEC 61557, EMC
- measurement category: IV 300 V acc. to EN 61010-1
- protection class acc. to EN 60529: IP54
Other technical specifications
- power supply:.................... Ni-MH rechargeable or LR14 alkaline disposable batteries
(4 pcs.) (optional)
.*For full Technical Specifications, please refer to PDF Data Sheet
Illuminance measurements:
- range of measurement: 0.1 lx...19.9 klx,
- measurement in lux (lx) or foot-candle (fc),
- measurement using external photo
detector (optional)
Standard Accessories for the MPI-530-IT & MPI-530:
Optional Accessories for the MPI-530-IT:
- Adapter with START button with UNI-Schuko (WS-03)
- Test lead with banana plug; 1,2m; yellow
- Test lead with banana plug; 1,2m; blue
- Test lead with banana plug; 1,2m; red
- Test lead on a reel with banana plugs; 15m; blue
- Test lead on a reel with banana plugs; 30m; red
- USB cable
- Pin probe with banana connector; yellow
- Pin probe with banana connector; red
- Pin probe with banana connector; blue
- "Crocodile" clip K02; yellow
- "Crocodile" clip K02; red
- Earth contact test probe (rod); 0,30m (2 pcs)
- Bluetooth mini-keyboard
- Carrying case L2
- Set of hanging straps
- NiMH rechargeable battery
- Lead for battery loading from the socked of car lighter (12V)
- Cable for battery charger
- Power supply adapter Z7
- Sonel Reader software
- Calibration certificate
- Adapter WS-04 with UNI-Schuko
- Adapter AutoISO 1000C
- Test lead on a reel with banana plugs; 50m;
- Test lead on a reel with banana plugs; 25m; blue
- Test lead with banana plug 5m; red
- Test lead with banana plugs; 10m; red
- Test lead with banana plug 20m; red
- Current clamp C 3
- Current clamp
- Transmitting clamp N1 (with test lead)
- Flexible clamp F-1 Ć 40cm
- Flexible clamp F-2 Ć 25cm
- Flexible clamp F-3 Ć 13cm
- Triple phase socket adapter AGT-16P
- Triple phase socket adapter AGT-32P
- Triple phase socket adapter AGT-63P
- Triple phase socket adapter AGT-16C
- Triple phase socket adapter AGT-32C
- Adapter for industrial sockets AGT-16T
- Adapter for industrial sockets AGT-32T
- Light meter probe LP1 with WS-06 plug
- Box for batteries
- Mini bluetooth keyboard with casing
- RCD breaker testing adapter TWR-1J
- Earth contact test probe (rod); 0,80m
- Software for creation of documentation
from electrical measurements "Sonel Reports"
- Software „SONEL Schematic”
- Hardware Adapter for Sonel PE program